bios phenom 2 965

Personalizza e crea il tuo personal computer come l'hai sempre desiderato!

Moderatori: `knives`, Galai

bios phenom 2 965

Messaggiodi santograal76 il 10 ott 2009, 15:19

Buona sera a tutti, volevo sapere se secondo voi questo settaggio del bios puo' andar bene per elevare le prestazioni del mio amd.
è gradito ogni consiglio
grazie

MAIN
Legacy Diskette A [Disabled]
Primary IDE Master [Not Detected]
Primary IDE Slave [Not Detected]
SATA1 [Not Detected]
SATA2 [Not Detected]
SATA3 [Not Detected]
SATA4 [Not Detected]
Storage Configuration
On Chip SATA Channel [Enabled]
On Chip SATA Type [Raid]

ADVANCED
JumperFree Configuration
AI Overclocking [Manual]
FSB Frequency [200]
PCIE Frequency [100]
Processor Frequency Multiplier [x16.0 3200MHz]
Processor Voltage [1.3000]
Processor-NB Voltage [1.2000]
CPU VDDA Voltage [2.6v] setting for the cpu's voltage regulation circuits
CPU-NB HT Link Speed [1 GHz]
DDR Voltage [2.20]
Northbridge Voltage [Manual]
Hyper Transport Volatge [1.40v]
Core/PCIe Voltage [1.12] Sets the voltage supplied to the NB chip itself
NB PCIE PLL [1.9v]
Southbridge Voltage [1.22]
Auto Xpress [Disabled]
CPU Tweak [Disabled]

Memory Configuration
Bank Interleving [Auto]
Channel Interleaving XOR of Address bits [20:16,6]
MemClk Trisate C3/ATLVID [Disabled]
Memory Hole Remaping [Enabled]
Unganged Mode Support [Disabled]
Power Down Enable [Disabled]
Read Delay [1.0 Memory CLKs] direct correlation w/memory's latency. The lower the setting the lower the latency
DCQ Bypass Maximum [Auto]
DRAM Timing Configuration
Memory Clock Mode [Manual]
Memory Clock Value [800 MHz]
2T Mode [Enabled] Command rate setting
DRAM Timing Mode [DCT 0]
CAS Latency (CL) [5 CLK]
TCWL [5 CLK] added setting with bios 1002 (CAS write latency-the lower the setting the faster the writes)
TRCD [5 CLK]
TRP [5 CLK]
TRAS [18 CLK] bios 1002 overrides this setting: If tRTP is set to Auto then -2 from what the setting is. Any other tRTP setting and this is 18 no matter what the setting is.
tWR [4 CLK]
tRFC0 [127.5 ns]
tRFC1 [127.5 ns]
tRFC2 [127.5 ns]
tRFC3 [127.5 ns]
TRC [26 CLK] bios 1002 overrides this setting if tRTP is not on Auto. If tRTP is not on Auto this is 26.
TRRD [2 CLK]
tWTR [3 CLK] bios 1002 orverrides this setting if tRTP is not on Auto; the resulting setting will be reduced by 1 otherwise.
tRTP [2-4 CLK] In bios 0801 anything but auto and TRC and TRAS are overridden/0902 2-4 CLK and TRAS functions as set
tRWTTO [4 CLK] For my memory it is Auto or same as tWR or will not boot.
tWRRD [0 CLK] these last three settings are for module-to-module timings(For benches I set them to 0,1,2 respectively)
tWRWR [1 CLK]
tRDRD [2 CLK]
PLL1 Spread Spectrum [Disabled]
PLL2 Spread Spectrum [Disabled]
AI Clock Skew for Chennel A [Auto]
Current Clock Skew Advance300ps
AI Clock Skew for Channel B [Auto]
Current Clock Skew Advance300ps

AI Net 2
Marvell Post LAN cable [Disabled]

CPU Configuration
PRESS "F4"
GART Error Reporting [Disabled]
Microcode Updation [Disabled]
PRESS "F4"
Secure Virtual Machine Mode [Enabled]
AMD Cool 'n' Quiet Function [Disabled]
ACPI SRAT Table [Enabled]
AMD Live! [Disabled]

Chipset
PRESS "F4"
Primary Video Controller [PCIE GFX0-GFX2-GPP] this setting identifies the top blue slot as primary. GFX2 refers to the top black slot (Port #03)
PRESS "F4"
PCI Express Configuration
GFX Dual Slot Configuration [Enabled]
GFX Dual Slot Configuration [Disabled]
Peer-to-Peer among GFX/GFX2 [Disabled] this setting is for running cards connected to the top blue and black slots on equal status for issuing requests and commands
GPP Slots Power Limit, W [25]
Port #02 & #03 Features
Gen2 High Speed Mode [Software Switch] found this was the best setting for me according to 3DMark06
Link ASPM [L0s & L1] ASPM stands for Active State Power Mangement (google it and read if inclined)
Link Width [x8]
Slot Power Limit, W [175] Maximum wattage that can be supplied through the slot (0-250)
Port#04 through #10
Gen2 High Speed Mode [Disabled]
Link ASPM [Disabled]
Port#11 Features Bottom blue slot
Gen2 High Speed Mode [Software Switch]
Link ASPM [L0s & L1]
Link Width [x16]
Slot Power Limit, W [225]
NB-SB Port Features
NB-SB Link ASPM [L1]
NP NB-SB VC1 Traffic Support [Enabled] (virtual channel 1) helps with Isochronous Flow-Control Mode & voice over IP

Hyper Transport Configuration
Isochronous Flow-Control Mode [Enabled] Part of the HTT Spec since AGP 8X.
HT Link Tristate [CAD/CTL/CLK] Power feature (defined at bottom in more detail)
UnitID Clumping [UnitID 2/3&B/C] Helps with the Isochronous Flow-Control Mode (defined at bottom in more detail)
2xLCLK Mode [Disabled]
Onboard Devices Configuration
PRESS "F4"
Onboard Floppy Controller [Disabled] default is Enabled
Floppy Drive Swap [Disabled] left at default
PRESS "F4"
Serial Port1 Address [Disabled]
Serial Port1 Mode [Normal] left at default
HD Audio Azalia Device [Auto] left at default
Front Panel Support Type [HD Audio]
1394 [Disabled] added setting in 0801
WiFi [Enabled] added setting in 0801
Onboard LAN [Enable]
Onboard LAN Boot ROM [Disabled]
Marvell 6111 SATA Controller [Enable]
Marvell 6121 SATA Controller [Enable]
Marvell Option ROM [Disabled]
Primary Display Adapter [PCI-E]
PCI PnP
All settings left at default
USB Configuration
USB Functions [Enabled] default
USB 2.0 Controller [Enabled] default
USB 2.0 Controller Mode [HiSpeed] default is full speed (been that way for me in all the bios revisions so far)
BIOS EHCI Hand-Off [Enabled] default
Legacy USB Support [Enabled] default

POWER
Suspend Mode [S1 only] default is Auto
Report Video on S3 Resume [No] default
ACPI 2.0 Support [Enabled] missleading label - actually enables ACPI power management
ACPI APIC Support [Enabled] default
APM Configuration
all settings left at default
Harware Monitor
CPU Fan Warning Speed [Disabled]
Smart Q-Fan Function [Enabled] this is what the fourth pin is for on four pin fan connectors
Samrt Q-Fan Profile [Optimal] atm the cpu is idling at 29C

BOOT
Boot Device Priority
1st Boot Device [RAID:RAID Ary 1]
2nd Boot Device [Disabled]
Boot Settings Configuration
Quick Boot [Disabled]
Full Screen Logo [Enabled]
AddOn ROM Display Mode [Force BIOS]
Bootup Num-Lock [On]
Wait for 'F1' Error [Enabled]
Hit 'DEL' Message Display [Enabled]
Chassis Intrusion [Enabled]

Security
all settings left at default
santograal76
Cittadino verde
Cittadino verde
 
Messaggi: 5
Iscritto il: 29 set 2009, 13:10

 

Re: bios phenom 2 965

Messaggiodi Galai il 11 ott 2009, 23:08

ma hai fatto qualche cambiamento te? nel caso su che parametri hai agito?
Sempre in Rete.....There is no place like 127.0.0.1

AmdPlanet ha bisogno di te    

World Community Grid AMD Planet Team

La Romagna suona.. L'Italia balla

Carica le tue foto su PixDiff il nuovo servizio di Hosting & Upload by AmdPlanet

Tutti dicono che sono una persona orribile....ma non è vero....Ho il cuore di un ragazzino.......in un vaso sulla scrivania!!!!


Immagine
Avatar utente
Galai
Moderatore
Moderatore
 
Messaggi: 12521
Iscritto il: 29 ago 2005, 14:11
Località: Cesena


Torna a Configurazioni

Chi c’è in linea

Visitano il forum: Nessuno e 1 ospite