bios phenom 2 965

[santograal76]

Buona sera a tutti, volevo sapere se secondo voi questo settaggio del bios puo' andar bene per elevare le prestazioni del mio amd.
è gradito ogni consiglio
grazie

MAIN
Legacy Diskette A [Disabled]
Primary IDE Master [Not Detected]
Primary IDE Slave [Not Detected]
SATA1 [Not Detected]
SATA2 [Not Detected]
SATA3 [Not Detected]
SATA4 [Not Detected]
Storage Configuration
On Chip SATA Channel [Enabled]
On Chip SATA Type [Raid]

ADVANCED
JumperFree Configuration
AI Overclocking [Manual]
FSB Frequency [200]
PCIE Frequency [100]
Processor Frequency Multiplier [x16.0 3200MHz]
Processor Voltage [1.3000]
Processor-NB Voltage [1.2000]
CPU VDDA Voltage [2.6v] setting for the cpu's voltage regulation circuits
CPU-NB HT Link Speed [1 GHz]
DDR Voltage [2.20]
Northbridge Voltage [Manual]
Hyper Transport Volatge [1.40v]
Core/PCIe Voltage [1.12] Sets the voltage supplied to the NB chip itself
NB PCIE PLL [1.9v]
Southbridge Voltage [1.22]
Auto Xpress [Disabled]
CPU Tweak [Disabled]

Memory Configuration
Bank Interleving [Auto]
Channel Interleaving XOR of Address bits [20:16,6]
MemClk Trisate C3/ATLVID [Disabled]
Memory Hole Remaping [Enabled]
Unganged Mode Support [Disabled]
Power Down Enable [Disabled]
Read Delay [1.0 Memory CLKs] direct correlation w/memory's latency. The lower the setting the lower the latency
DCQ Bypass Maximum [Auto]
DRAM Timing Configuration
Memory Clock Mode [Manual]
Memory Clock Value [800 MHz]
2T Mode [Enabled] Command rate setting
DRAM Timing Mode [DCT 0]
CAS Latency (CL) [5 CLK]
TCWL [5 CLK] added setting with bios 1002 (CAS write latency-the lower the setting the faster the writes)
TRCD [5 CLK]
TRP [5 CLK]
TRAS [18 CLK] bios 1002 overrides this setting: If tRTP is set to Auto then -2 from what the setting is. Any other tRTP setting and this is 18 no matter what the setting is.
tWR [4 CLK]
tRFC0 [127.5 ns]
tRFC1 [127.5 ns]
tRFC2 [127.5 ns]
tRFC3 [127.5 ns]
TRC [26 CLK] bios 1002 overrides this setting if tRTP is not on Auto. If tRTP is not on Auto this is 26.
TRRD [2 CLK]
tWTR [3 CLK] bios 1002 orverrides this setting if tRTP is not on Auto; the resulting setting will be reduced by 1 otherwise.
tRTP [2-4 CLK] In bios 0801 anything but auto and TRC and TRAS are overridden/0902 2-4 CLK and TRAS functions as set
tRWTTO [4 CLK] For my memory it is Auto or same as tWR or will not boot.
tWRRD [0 CLK] these last three settings are for module-to-module timings(For benches I set them to 0,1,2 respectively)
tWRWR [1 CLK]
tRDRD [2 CLK]
PLL1 Spread Spectrum [Disabled]
PLL2 Spread Spectrum [Disabled]
AI Clock Skew for Chennel A [Auto]
Current Clock Skew Advance300ps
AI Clock Skew for Channel B [Auto]
Current Clock Skew Advance300ps

AI Net 2
Marvell Post LAN cable [Disabled]

CPU Configuration
PRESS "F4"
GART Error Reporting [Disabled]
Microcode Updation [Disabled]
PRESS "F4"
Secure Virtual Machine Mode [Enabled]
AMD Cool 'n' Quiet Function [Disabled]
ACPI SRAT Table [Enabled]
AMD Live! [Disabled]

Chipset
PRESS "F4"
Primary Video Controller [PCIE GFX0-GFX2-GPP] this setting identifies the top blue slot as primary. GFX2 refers to the top black slot (Port #03)
PRESS "F4"
PCI Express Configuration
GFX Dual Slot Configuration [Enabled]
GFX Dual Slot Configuration [Disabled]
Peer-to-Peer among GFX/GFX2 [Disabled] this setting is for running cards connected to the top blue and black slots on equal status for issuing requests and commands
GPP Slots Power Limit, W [25]
Port #02 & #03 Features
Gen2 High Speed Mode [Software Switch] found this was the best setting for me according to 3DMark06
Link ASPM [L0s & L1] ASPM stands for Active State Power Mangement (google it and read if inclined)
Link Width [x8]
Slot Power Limit, W [175] Maximum wattage that can be supplied through the slot (0-250)
Port#04 through #10
Gen2 High Speed Mode [Disabled]
Link ASPM [Disabled]
Port#11 Features Bottom blue slot
Gen2 High Speed Mode [Software Switch]
Link ASPM [L0s & L1]
Link Width [x16]
Slot Power Limit, W [225]
NB-SB Port Features
NB-SB Link ASPM [L1]
NP NB-SB VC1 Traffic Support [Enabled] (virtual channel 1) helps with Isochronous Flow-Control Mode & voice over IP

Hyper Transport Configuration
Isochronous Flow-Control Mode [Enabled] Part of the HTT Spec since AGP 8X.
HT Link Tristate [CAD/CTL/CLK] Power feature (defined at bottom in more detail)
UnitID Clumping [UnitID 2/3&B/C] Helps with the Isochronous Flow-Control Mode (defined at bottom in more detail)
2xLCLK Mode [Disabled]
Onboard Devices Configuration
PRESS "F4"
Onboard Floppy Controller [Disabled] default is Enabled
Floppy Drive Swap [Disabled] left at default
PRESS "F4"
Serial Port1 Address [Disabled]
Serial Port1 Mode [Normal] left at default
HD Audio Azalia Device [Auto] left at default
Front Panel Support Type [HD Audio]
1394 [Disabled] added setting in 0801
WiFi [Enabled] added setting in 0801
Onboard LAN [Enable]
Onboard LAN Boot ROM [Disabled]
Marvell 6111 SATA Controller [Enable]
Marvell 6121 SATA Controller [Enable]
Marvell Option ROM [Disabled]
Primary Display Adapter [PCI-E]
PCI PnP
All settings left at default
USB Configuration
USB Functions [Enabled] default
USB 2.0 Controller [Enabled] default
USB 2.0 Controller Mode [HiSpeed] default is full speed (been that way for me in all the bios revisions so far)
BIOS EHCI Hand-Off [Enabled] default
Legacy USB Support [Enabled] default

POWER
Suspend Mode [S1 only] default is Auto
Report Video on S3 Resume [No] default
ACPI 2.0 Support [Enabled] missleading label - actually enables ACPI power management
ACPI APIC Support [Enabled] default
APM Configuration
all settings left at default
Harware Monitor
CPU Fan Warning Speed [Disabled]
Smart Q-Fan Function [Enabled] this is what the fourth pin is for on four pin fan connectors
Samrt Q-Fan Profile [Optimal] atm the cpu is idling at 29C

BOOT
Boot Device Priority
1st Boot Device [RAID:RAID Ary 1]
2nd Boot Device [Disabled]
Boot Settings Configuration
Quick Boot [Disabled]
Full Screen Logo [Enabled]
AddOn ROM Display Mode [Force BIOS]
Bootup Num-Lock [On]
Wait for 'F1' Error [Enabled]
Hit 'DEL' Message Display [Enabled]
Chassis Intrusion [Enabled]

Security
all settings left at default

[Galai]

ma hai fatto qualche cambiamento te? nel caso su che parametri hai agito?